KS Flow Control Lifting Rigging & Mooring

LIFTING, RIGGING & MOORING

Backed by a diverse portfolio of trusted brands, an extensive product range, and a team of trained specialists, KS Flow Control delivers reliable, end-to-end solutions for all your below-the-hook lifting needs.

Vertical Lifting Clamp

IPU10 Series

(Universal - for lifting in any direction)

Available in a variety of styles:

IPU10 - Standard clamp for materials with a surface hardness to 363HV10 (345 HB).
IPU10J - Larger jaw opening.
IPU10S - For use with stainless steel material.
IPU10H - For use with materials with a surface hardness to 472HV10 (450 HB).

Available in capacities of 0.5 thru 30 metric tons .
Wide variety of jaw openings available: 0” to 6.13”.
Full 180° turning range for material transfer, turning or moving.
All sizes are RFID equipped.

IPU10

IPU10S

IP10 Series

(For vertical lifting, turning and transfer)

IP10

Available in a variety of styles:

IP10 - Standard clamp for materials with a surface hardness to 363HV10 (345 HB).
IP10J - Larger jaw opening.
IP10S - For use with stainless steel material.
IP10H - For use with materials with a surface hardness to 472HV10 (450 HB).

Available in capacities of 0.5 thru 30 metric tons.
Wide variety of jaw openings available: 0” to 6.13”.
Full 180° turning range for material transfer, turning or moving.
All sizes are RFID equipped.

IP10S

IPNM Series

(For vertical lifting, turning and transfer of Non-Marring material)

Available in a variety of styles:

IPNM10N - Standard clamp for materials such as aluminum, stainless steel, painted materials, aircraft skins, composite material, glass, plastic, etc
IPNM10P - With protection cap
IPNM10NJ - With larger jaw opening

Without marring the surface of the material.
Available in capacities of 0.5, 1 and 2 metric tons.
Wide variety of jaw openings available: 0” to 1.56”.
Full 180° turning range for material transfer, turning or moving.
All sizes are RFID equipped.

IPNM10N

IPNM10P

IPU10A

(Universal - for lifting in any direction)

IPU10A

IPU10A automatically clicks onto the material as soon as the clamp is placed on the plate. The fact that the safety lock remains in position as the clamp closes precludes hazardous situations. Fastening the IPU10A clamp in places that are difficult to reach is no problem.

Available in capacities of 1, 2 and 6 metric tons.
Jaw openings available: 0” to 2”.
Full 180° turning range for material transfer, turning or moving.
All sizes are RFID equipped.

Horizontal Lifting Clamps

IPH10 Series

(For Horizontal Lift and Transfer with Pretension System)

IPH10

IPHNM10

Available in a variety of styles:

IPH10 - With Spring Loaded Tension, Magnets and Handle.
IPH10J – With larger jaw opening.
IPHNM10 – Non-Marring Model

Available in capacities of 0.5 thru 12 metric tons .
Wide variety of jaw openings available: 0” to 4.75”.
Horizontal lifting and transfer of non-sagging material.
All sizes are RFID equipped.

IPH10 Series
(For Horizontal Lift and Transfer)

IPH10E

Available in a variety of styles:

IPH10E – Standard Horizontal Lift and Transfer Clamp
IPH10JE - With larger jaw opening.

Available in capacities of 2.0 thru 25 metric tons .
Wide variety of jaw openings available: 0” to 4.75”.
Horizontal lifting and transfer of non-sagging material / bundles of non-sagging material
All sizes are RFID equipped.

IPHOZ Series
(For Horizontal Lift and Transfer of Thin Sheet / Materials that will Sag or Bend)

IPHOZ

IPHOZ horizontal lifting clamp is to be used for lifting and transferring, in the horizontal position, of thin sheet and other materials that will sag or bend when lifted.

Available in capacities of 0.75 through 15 metric tons
Wide variety of jaw openings available: 0” to 2.38”.
Lifting and transferring, in the horizontal position, of thin sheet and other materials that will sag or bend when lifted.
All sizes are RFID equipped.

IPPE10 Series
(For Lifting and Transporting Non-Bendable Sheet Metal in a Horizontal Position.)

Available in a variety of styles:

IPPE10B: Magnets in foot plate (also applies for D and H Type).
IPPE10BE: Economic version (also applies for D and H-Type).
IPPE10BNM: Non-marring (also applies for D and H-Type).

Also Available in :

D-Type (maximum jaw opening of 11.75”)
H-Type (maximum jaw opening of 16.50”)

IPPE10B(E)

IPPE10BNM

Available in capacities of 3 through 12 metric tons.
Wide variety of jaw openings available: 0” to 7.13”.
The jaw opening can be easily adjusted for the height of the bundle or plate.
All sizes are RFID equipped.

IPBC & IPHGUZ Series

(For Horizontal Transfer - with Pretension System)

IPBC

IPHGUZ

Available in a variety of styles:

IPBC: with Pretension System
IPHGZ: Fixed Hoisting Eye
IPHGUZ: Universal Lifting Eye

Available in capacities of 1 through 4.5 metric tons.
Wide variety of jaw openings available: 0” to 1.56”.
Horizontal lifting and transfer of sagging and non-sagging material.
May also be used for turning beams from the “H” into the “I” position.
All sizes are RFID equipped.

Beam Clamp

IPBK10 Beam Clamp
(For the transfer and stacking of steel beams)

IPBK10 beam clamp is used for lifting, transferring and stacking H-Beams. A ring-center hoist eye allows for the beam flange to remain vertical.
This series of clamps can be used in vertical and horizontal moving, transferring and stacking of different types of structural designs, such as H-Beams, angles, etc, depending on the application desired.

Available in capacities of 0.5 through 4 metric tons.
Jaw openings available: 0.2 to 1.13”.
All sizes are RFID equipped.

IPBK10

IPVUZ Series Beam Clamp
(For the transfer and stacking of steel beams)

IPVUZ

Available in a variety of styles:

IPVUZ: Universal Hoisting Eye
IPVZ: Fixed Hoisting Eye

Available in capacities of 0.75 through 1.5 metric tons.
Jaw openings available: 0 to 0.81”.
Vertical lift and transfer of angle iron and other loads that have only a small gripping area for the clamp (“U” has universal hoisting eye)
Used in vertical and horizontal moving, transferring and stacking of different types of structural designs, such as H-beams, angles, etc, depending on the application desired.
All sizes are RFID equipped.

IPBHZ Beam Clamp
(For the lifting and transfer of steel beams)

IPBHZ beam clamp is used for lifting, transferring and stacking H-Beams. An ring-center hoist eye allows for the beam flange to remain vertical.
This series of clamps can be used in vertical and horizontal moving, transferring and stacking of different types of structural designs, such as H-Beams, angles, etc, depending on the application desired.

Available in capacities of .75 through 12 metric tons
Wide variety of jaw openings available: 0 to 1.56”.
All sizes are RFID equipped.

IPBHZ

IPBSNZ Series Beam Clamp
(For the lifting and transfer of steel beams)

IPBSNZ beam clamp is used for lifting, transferring and stacking H-Beams. An ring-center hoist eye allows for the beam flange to remain vertical.
This series of clamps can be used in vertical and horizontal moving, transferring and stacking of different types of structural designs, such as H-Beams, angles, etc, depending on the application desired.

Available in capacities of 1.5 through 4.5 metric tons
Wide variety of jaw openings available: 0 to 2.00”.
All sizes are RFID equipped.

IPBSNZ

IPTK Series

(For transferring steel beams and attaching tackle eye)

IPTK

IPTKW

Available in a variety of styles:

IPTK: with hoisting eye
IPTKW: without hoisting eye

Available in capacities of 1 through 4.5 metric tons.
Wide variety of jaw openings available: 0” to 1.56”.
Horizontal lifting and transfer of sagging and non-sagging material.
May also be used for turning beams from the “H” into the “I” position.
All sizes are RFID equipped.

IPTK Series
(For transferring steel beams and attaching tackle eye)

IPTKU

IPTKUM

Available in a variety of styles:

IPTKU: with improved hinged hoisting eye
IPTKUD: with optional double locking device
IPTKUM: Suitable as anchor device for personnel fall arrest equipment

Available in capacities of 2 through 25 metric tons
Wide variety of jaw openings available: 2.95” to 40.16”.
Suitable for use as a temporary tackle eye for a beam
All sizes are RFID equipped.

IPTKA
(Universal Beam Clamp)

IPBSNZ

Multi-purpose hoisting eye to be used for tightening as well as for hoisting.
Maintains full WLL at angles up to 90°.
Bail swivels 360° and pivots 180°.
Easy to close and open with a hinged body with self-locking device.
Easy to handle with handgrips.
No interference or space limitations when tightening the clamp.
Light weight design.

Available in capacities of 3 through 15 metric tons
Wide variety of jaw openings available: 3.9” to 16”.
All sizes are RFID equipped.

IPBCF / IPBCNS Series Beam Clamp
(For the lifting and transfer of wide flange beam sections and plate girders)

IPBCF / IPBCNS

IPBCNS clamps have a recessed base to accept studs welded to the beam surface.
Eliminates the need for slings, chokers, and spreader bars.
When applied to load, the tongs automatically open and slide under the flange of the beam.
Center plate and gripping tongs work together - the heavier the beam, the greater the clamping pressure.

Available in capacities of 4.5 through 32 metric tons
Flange grip range: 4” to 36” (width) & 0.5” to 4” (thickness)
All sizes are RFID equipped.

Positioning Clamp

IPSC10
(For positioning, pulling and turning plates or fabrications)

Suitable for use in positioning & turning steel plates and sections.
Not to be used as a lifting clamp.
Suitable for steel with a surface hardness up to 30 Rc.

Available in capacities of 1.5 through 3 metric tons
Wide variety of jaw openings available: 0” to 2.38”.
All sizes are RFID equipped.

IPSC10

Shipbuilding Clamp

IPBTO10
(For positioning, pulling and turning plates or fabrications)

IPBTO10

IPSC10 screw style clamp is use as a temporary tackle eye in spaces that have been reinforced with HP (bulb) profiles such as engine rooms and shipsections.

Available in capacities of 1.5 through 6 metric tons
Wide variety of jaw openings available: HP 6.5” to HP 17”.
Profile: Holland Bulb (HP) style and size material.
All sizes are RFID equipped.

IPBUZ

(For positioning, pulling and turning plates or fabrications)

IPBUZ

IPBUUZ

Available in a variety of styles:

IPBUZ shipbuilding clamps are used for lifting, transferring and placing bulb profiles onto ship’s hulls perpendicularly.
These clamps are fitted with a locking device for both open and closed positions, which ensures complete reliability.
They are to be used exclusively for bulb profiles (not for plates).
IPBUZ: with Fixed Hoisting Eye
IPBUUZ: with Universal Hoisting Eye

Available in capacities of 0.75 through 3.75 metric tons
Jaw openings available: HP 4.75” to HP 17”.
Profile: Holland Bulb (HP) style and size material.
All sizes are RFID equipped.

IPBUZ
(For Lifting, Transferring and Placing Complete Shipsections)

IPSBUUZ

The IPSBU(U)Z shipbuilding clamps are used for the lifting, transfer and placing of complete shipsections.
These clamps are fitted with a locking device for both open and closed positions, which ensures complete reliability.
They are to be used exclusively for bulb profiles (not for plates).
IPSBUZ / IPSBUSZ: With Fixed Hoisting Eye.
IPSBUUZ / IPSBUSUZ: With Universal Hoisting Eye.

Available in capacities of 4.5 through 22.50 metric tons
Jaw openings available: HP 4” to HP 17”.
Profile: Holland Bulb (HP) style and size material.
All sizes are RFID equipped.

Drum Clamp

IPDV
(Designed to lift, move and transfer 50-55 gallon drums with steel tops)

IPDV

IPVK

IPDV drum clamp is for vertical lift and transfer. Allows drum to remain in an upright position during the lift and transfer using one clamp.
IPDV Jaw openings: 11.75”

IPVK drum clamp is for vertical lift and transfer. Automatically locks on drum, and can be used alone or in pairs.
IPVK Jaw openings: 0.63”

Available in capacities of 0.5 metric tons
All sizes are RFID equipped.

Concrete Clamp

IPCC
(For Lifting and Transferring Concrete Pipe Sections and Wells)

IPCC

IPCC is suitable for the vertical lifting and transfer of concrete pipe sections and wells.
Very easy application and removal of the clamp thanks to the built-in carrying-grips.
Normally used in combination with 7mm chain (not supplied). These clamps must be used in pairs or more.

Available in capacities of 1 metric tons
Jaw opening available: 1.56” - 5.50”.
All sizes are RFID equipped.

IPBG
(Provides a fast and efficient method for handling road barriers.)

IPBG Comes equipped with polyurethane pads.
Hands-free operation.
Welded alloy steel construction for strength and smaller size.

Available in capacities of 4 metric tons
Jaw opening available: 6” - 12”.
All sizes are RFID equipped.

IPBG

Wire Rope Clip

Crosby Clip G-450

Forged: Crosby Red U-Bolt Clips have forged bases on all sizes, except 2-3/4" and 3-1/2" base is a steel casting. The entire clip is galvanized to resist corrosive and rusting action. Clip sizes 1/8" through 1-1/2" have U-Bolts with rolled threads which enhance the strength of the material and fatigue properties.

Soft Eye Bundle Clip

G-460

Thimble Eye Bundle Clip

G-461

Fist Grip® Clips G-429

3/16” to 5/8”

3/4” to 1-1/2”

Forged: Fist Grip Clips are forged, and the entire clip is galvanized. The double saddle design eliminates the possibility of incorrect installation. Designed as an integral part of the clip, the bolts are opposite one. As result, the nuts can be installed in such a way as to enable the operator to swing the wrench in a full arc for ease of installation

Forged bases and bundle clip adapters.
All bundle clips are individually bagged or tagged with proper application instructions and warning information.
Bundle Clip Adapter for Soft Eye (G4460) and for Thimble Eye (G4461) kits available.
Meets or exceeds all requirements of ASME B30.26 including manufacturing ID and size requirements. Importantly, these wire rope bundle clips meet material traceability not addressed by ASME B30.26.

Wedge Socket

Spelter Socket

Wedge Socket

S-421T

Utility Wedge Sockets

US-422T

SUPER TERMINATOR®

Wedge Socket

S-423T

Open Spelter Sockets

G-416

Closed Spelter Sockets

G-417

Button Spelter Sockets

SB-427

Resin for Spelter Socket

Swage Socket

WIRELOCK® Socketing Compound

(For use on 416, 417, 427 and 517 spelter sockets only.)

100% termination efficiency.

Temperature operating range is -65° F to +240° F (-54°C to +116°C).

Ideal for on-site applications.

No hazardous molten metal.

Improved fatigue life.

Pouring temperature without booster pack is 48° F to 110° F (6.67°C to 43.3°C).

One booster pack if pouring temperature is 35° F to 48° F (1.67°C to 8.89°C).

Two booster packs if pouring temperature is 27° F to 35° F (-2.78°C to +1.67°C).

Open Swage Sockets

S-501

Close Swage Sockets

S-502

Forged from special bar quality carbon steel, suitable for cold forming.
Swage socket terminations have an efficiency rating of 100% based on the catalog strength of wire rope.
Hardness controlled by spheroidize annealing.
Stamp for identification after swaging without concern for fractures (as per directions in Wire Rope End Terminations User’s Manual).

Swage sockets incorporate a reduced machined area of the shank which is equivalent to the proper 'after swage' dimension. Before swaging, this provides for an obvious visual difference in the shank diameter. After swaging, a uniform shank diameter is created allowing for a QUIC-CHECK® and permanent visual inspection opportunity.
In accordance with ASME B30.9, all slings terminated with swage sockets shall be proof loaded.*
Swage Sockets are recommended for use with 6 x 19 or 6 x 37, IPS or XIP (EIP), XXIP (EEIP), RRL, FC or IWRC wire rope.

COLD TUFF® Swaging Sleeve

COLD TUFF®

Standard Steel Sleeves (S-505)

For flemish eye wire rope splicing.
Designed for low temperature toughness.
Resists cracking when swaged (equals or exceeds stainless steel sleeves).

Termination Effeciency:

COLD TUFF®

Steel Swage Button (S-409)

COLD TUFF®

Duplex Non-Tapered Sleeve (S-506)

S-409 Buttons are recommended for use with 6 x 19 or 6 x 37, IPS or XIP (EIP), RRL, FC or IWRC wire rope.

For turnback wire rope splicing.
Resists cracking when swaged (equals or exceeds stainless steel sleeves).

Termination Effeciency:

Swage button terminations have an efficiency rating of 98% based on the catalog strength of wire rope.

Rope Sizes:

1/8" to 1-1/4" (inches)

3 to 32 (mm)

Termination Effeciency:

Turnback terminations have efficiency ratings of 94% based on the catalog strength of wire rope.

Rope Sizes:

1/2" to 1-1/2" (inches)

13 to 38 (mm)

Rope Sizes:

1/2" to 3-1/2" (inches)

12 to 84 (mm)

Wire Rope Thimble

Standard Wire Rope Thimble (G-411)

Hot-dip galvanised steel.
The standard choice for light duty loading conditions and applications.
Meets the performance requirements of Federal Specification FF-T-276b Type II, except for those provisions required of the contractor

Open Pattern Thimbles (G-408)

Hot-dip galvanised steel.
Recommended for light duty applications where assembly into another fitting (i.e., shackle or master link) is required.

Extra Heavy Wire Rope Thimbles (G-414)

Available in hot-dip galvanised or stainless steel (Type 304).
Greater protection against wear and deformation of the wire rope eye.
Longer service life.
Meets the performance requirements of Federal Specification FF-T-276b Type III, except for those provisions required of the contractor.

Rope Diameter:

1/8" to 1-1/4" (inches)

3 to 32 (mm)

Rope Diameter:

1/4" to 5/8" (inches)

6 to 16 (mm)

Rope Diameter:

1/4" to 2-1/4" (inches)

6 to 56 (mm)

Solid Wire Rope Thimbles (S-412)

Cast ductile iron.
Fits pin for open wire rope socket, boom pendant clevis, and wedge socket.

Extra Heavy Wire Rope Thimbles (Shackle-Loc) (G-414SL)

Prevents the shackle from being removed and replaced in the field, which could compromise the certified integrity of the sling assembly.
Available in hot-dip galvanised. Crosby’s shackle locking thimbles are galvanised after the welding of the wedge has been completed.
Greater protection against wear and deformation of the wire rope eye.
Longer service life.
Meets the performance requirements of Federal Specification FF-T-276b Type III, except for those provisions required of the contractor.

Rope Diameter:

1/2" to 1-3/8" (inches)

13 to 35 (mm)

3/8" to 1-1/2" (inches)

9 to 38 (mm)

Wire Rope Lubricant

Vitalife®

Vitalife® products are the preferred wire rope lubricants in the industry because of their ability to penetrate into wire rope and displace water and contaminants, thus reducing wear and corrosion throughout the rope.

Available in a variety of container sizes.
Provides inner strand preservation and lubricity.
Allows for easy visual inspection of the ropes.
Reduces the friction between the strands of the wire rope, thus extending rope life.
Adheres to surface of strands, forming an outer film which provides excellent corrosive protection.
Non-tacky (will not attract dust)
Vitalife® in aerosol form is a regulated dangerous good
Vitalife® Bio-Lube has been developed especially for environmentally friendly applications.
Vitalife® 500 has been developed exclusively for ski lifts and tramways.

VITALIFE® 400

12 OZ.

VITALIFE® 410 BIO-LUBE

12 OZ.

VITALIFE® 400

5 GALLON

VITALIFE® 400

55 GALLON

Master Link & Assembly

The Crosby Group offers a wide range of links, from small 1,800 lb capacities all the way up to 395,000 lbs, as well as application-specific links, such as the hot-dip galvanised master links for use in highly corrosive environments.

Alloy Master Links A-342

Grade 100 Welded Master Link A-1343

Grade 80 Welded Master Links with Engineered Flat A-344

Master Link Assembly with Engineered Flat A-1346

Grade 100 Welded Master Link Assembly A-1346

Grade 80 Welded Master Links with Engineered Flat A-347

Weldless Link

Weldless End Links

G-340/ S-340

Forged carbon steel - Quenched & Tempered Self colored (S) or hot-dip galvanized (G).

Round Pin Chain Shackles S-642

Forged carbon steel - Quenched & Tempered. Self Colored

Alloy Pear Shaped Links A-341

Alloy steel — Quenched & Tempered.
Individually Proof Tested at 2 times Working Load Limit with certification.
Proof Test certification shipped with each link.
Sizes up to 2" are forged.

Round Pin Chain Shackles S-642

Forged carbon steel - Quenched & Tempered.
Self colored (S) or hot-dip galvanised (G).

Eliminator

The Crosby Eliminator® combines selected features and functionality of a master link, connecting link, grab hook and adjuster legs to provide you with one fitting that is suitable for applications that require an adjustable length chain sling.

Eliminator® Single Hook (A-342)

Chain Size:

1/2" to 5/8" (inches)

7-16 (mm)

Working Load Limit (lbs)

4,300 to 22,600

Eliminator® Double Hook (A-1362)

Chain Size:

1/2" to 5/8" (inches)

7-16 (mm)

Working Load Limit (lbs)

8,600 to 45,200

Alloy Chain

Recommended for overhead lifting applications

Spectrum 8® Grade 80 Alloy Chain

Chain Size:

9/32" to 1-1/4" (inches)

7-32 (mm)

Working Load Limit (lbs)

3,500 to 72,300

Spectrum 10® Grade 100 Alloy Chain

Chain Size:

9/32" to 1-1/4" (inches)

7-16 (mm)

Working Load Limit (lbs)

4,300 to 90,400

Connecting Link

LOK-A-LOY® 10 Alloy Connecting Link

(A-1337)

Chain Size:

9/32" to 1-1/4" (inches)

7-32 (mm)

Working Load Limit (lbs)

4,300 to 90,400

Grade 100 Chain Coupler (S-1325A)

Chain Size:

1/4" to 5/8" (inches)

6-16 (mm)

Working Load Limit (lbs)

4,300 to 90,400

Grade 100 Chain Shortener Link (S-1311N)

Chain Size:

1/4" to 5/8" (inches)

6-16 (mm)

Working Load Limit (lbs)

3,200 to 22,600

Reeving Link (A-1370)

Pear Shape “Missing Link”® Replacement Links (G-334)

Chain Size:

1/4" to 5/8" (inches)

7-16 (mm)

Working Load Limit (lbs)

5,700 to 22,600

Not suitable for use with Grade 80 or Grade 100 chain and chain slings used in overhead lifting.

Chain Size:

3/8" to 7/8" (inches)

10-22 (mm)

Working Load Limit (lbs)

1,850 to 9,600

“Missing Link”® Replacement Links

(G-335)

Not suitable for use with Grade 80 or Grade 100 chain and chain slings used in overhead lifting.

Chain Size:

1/4" to 1" (inches)

7-26 (mm)

Working Load Limit (lbs)

1,325 to 15,500

Sling Identification Tag Kit

Quick-Tag™ with RFID Chip

Features:

Easy, fast and secure attachment
Engineered for extreme durability and strength with a low profile design
Resistant to harsh environmental conditions including exposure to UV rays, water chemical exposure and temperatures up to 185˚F (85˚C)
Compatible with the Crosby QUIC-CHECK® Inspection and Identification System
The most cost effective RFID tag offered by Crosby®

RFID Synthetic Sling Tag Kit

RFID Chip Size

RFID Block Tag Kit

RFID Hoist Ring Tag Kit

Cast HF RFID Wire Rope Tag

Steel RFID Wire Rope Tag

Cast HF RFID Chain Tag

Steel RFID Chain Tag

Sling Hooks

Eye Sling Hook (L-1327)

Chain Size:

1/4" to 1-1/4" (inches)

6-32 (mm)

Working Load Limit (lbs)

3,200 to 90,400

Clevis Sling Hook (L-1339)

Chain Size:

1/4" to 7/8" (inches)

6-23 (mm)

Working Load Limit (lbs)

1/2 to 35

SHUR-LOC® Eye Hook with Positive Locking Latch (A-1316AH)

Chain Size:

5/8" to 1" (inches)

16-26 (mm)

Working Load Limit (lbs)

22,600 to 59,700

SHUR-LOC® Handle Swivel Hooks with Bearings (S13326H)

Chain Size:

5/8" to 1" (inches)

16-26 (mm)

Working Load Limit (lbs)

22,600 to 59,700

SHUR-LOC Hooks

SHUR-LOC® Eye Hook with Positive Locking Latch (S-1316)

SHUR-LOC® Swivel Hooks (S-1326)

Reeving Link (A-1370)

Chain Size:

1/4" to 1" (inches)

6-26 (mm)

Chain Size:

1/4" to 7/8" (inches)

9-23 (mm)

Chain Size:

1/4" to 5/8" (inches)

6-22 (mm)

Working Load Limit (lbs)

3,200 to 50,700

Working Load Limit (lbs)

1/2 to 35

Working Load Limit (lbs)

2,560 to 34,160

SHUR-LOC® Swivel Hooks with Bearing (S-13326)

Chain Size:

1/4" to 5/8" (inches)

6-16 (mm)

Working Load Limit (lbs)

3,200 to 22,600

Grab Hooks

Eye Grab Hook (A-1328)

Chain Size:

1/4" to 1-1/4" (inches)

6-32 (mm)

Working Load Limit (lbs)

5,700 to 90,400

Grab Hook (A-1358)

Chain Size:

1/4" to 5/8" (inches)

6-16 (mm)

Working Load Limit (lbs)

4,300 to 22,600

Eye Cradle Grab Hook (A-1348)

Chain Size:

1/4" to 5/8" (inches)

6-16 (mm)

Working Load Limit (lbs)

5,700 to 22,600

Grab Hook with Latch (L-1358)

Chain Size:

1/4" to 5/8" (inches)

6-16 (mm)

Working Load Limit (lbs)

4,300 to 22,600

Cradle Grab Hook (A-1338)

Chain Size:

1/4" to 5/8" (inches)

6-16 (mm)

Working Load Limit (lbs)

4,300 to 22,600

Eye Grab Hooks (A-323)

Chain Size:

1/4" to 3/4" (inches)

7-19 (mm)

Working Load Limit (lbs)

3,500 to 24,700

Cradle Grab Hook with Latch (L-1338)

Chain Size:

1/4" to 5/8" (inches)

6-16 (mm)

Working Load Limit (lbs)

4,300 to 22,600

Clevis Grab Hooks (A-330)

Chain Size:

1/4" to 3/4" (inches)

7-19 (mm)

Working Load Limit (lbs)

3,500 to 24,700

Chain Hooks

Eye Chain Hook with Integrated Latch (S-315A)

Chain Size:

1/4" to 5/8" (inches)

6-16 (mm)

Working Load Limit (lbs)

2,500 to 18,100

Clevis Chain Hook with Integrated Latch (S-314A)

Chain Size:

1/4" to 5/8" (inches)

7-16 (mm)

Working Load Limit (lbs)

2,500 to 18,100

Chain Nest Hooks (O-318)

Chain Size:

1/4" to 9/16" (inches)

6-16 (mm)

Working Load Limit (lbs)

1.5 to 3.8

Chain Nest Hooks (O-319)

Chain Size:

1/4" to 9/16" (inches)

6-16 (mm)

Working Load Limit (lbs)

1.5 to 3.8

Golden Gate Hooks

Gate Type

Brass alloy Golden Gates® are engineered for quality, easy handling and dependability. The heavy duty, corrosion resistant locking mechanism will stay locked until an operator releases it; yet, can easily be shut with one hand. Cost effective, these gates reduce down time, providing the alternative to conventional latches.

LIF-LOK® GATE

To Lock:

Close the gate; the built-in spring locks the gate against the hook tip.

To Unlock:

Lift the gate upward on the hook shank and swing open.

PIN-LOK® GATE

To Lock:

Close the gate; a stainless steel pin is carried in a horizontal bore and engages a milled slot in the hook shank.

To Unlock:

Simply depress the stainless steel pin which causes the pin to disengage from the milled slot.

ROLLOX® GATE

To Lock:

Close the gate; a stainless steel pin is mounted in a horizontal bore which passes through the gate and engages a notch milled in the hook shank.

To Unlock:

Move the lever downward a quarter-turn or until it stops, the gate can now swing open 160 ° (approx.)

TIP-LOK® GATE

To Lock:

Press the arm down until the lock trips; two arms of the gate now enclose the tip of the hook.

To Unlock:

Manually depressing the locking trigger automatically raises the movable arm, allowing the gate to be rotated open.

Gate Type

The 5 connector styles shown below make it possible for Crosby to furnish a Golden Gate Hook to fit almost any make or model of hoisting equipment including, American Engineering Lo-Hed, ARO, Coffing, Electro Lift, Ingersoll-Rand, P & H, Robbins and Myers, Shepard Niles, CM, Shaw-Box, Wright, Yale & Towne.

CLOSED SWIVEL BAIL

Description:

For use where hoisting line or shackle can be inserted into the bail. Suitable for positioning before lifting.

STANDARD SHANK-TYPE HOOK

Description:

For use on existing load blocks, with standard shank length.

LONG SHANK-TYPE HOOK

Description:

For use on existing load blocks requiring extra shank length.

UNIVERSAL TYPE

LINK CHAIN NEST

Description:

Open swivel bail for attachment to link chain. Suitable for positioning before lifting.

Description:

With ball-bearing swivel; attaches to chain by an alloy pin. Suitable for frequent rotation under load.

Choker Hooks

Foundry Hook

Chain Choker Hook (A-1355)

Sliding Choker Hook (A-350L)

Eye Foundry Hook (A-1329)

Clevis Foundry Hook (A-1359)

Chain Size:

1/4" to 5/8" (inches)

7-16 (mm)

Working Load Limit (lbs)

5,700 to 22,600

Chain Size:

3/8" to 1" (inches)

10-25 (mm)

Working Load Limit (lbs)

2,500 to 15,000

Chain Size:

1/4" to 1-1/4" (inches)

7-32 (mm)

Working Load Limit (lbs)

5,700 to 90,400 (Saddle)

2,850 to 45,200 (Tip)

Chain Size:

1/4" to 7/8" (inches)

7-23 (mm)

Working Load Limit (lbs)

4,300 to 2,150 (Saddle)

44,100 to 22,050 (Tip)

Special Application Hooks

Sorting Hook (A-378)

Description:

Forged alloy steel, Quenched & Tempered.
Deep straight throat permits efficient handling of flat plates or large cylindrical shapes.

Sorting Hook with Handle (A-378)

Description:

Forged alloy steel, Quenched & Tempered.
Deep straight throat permits efficient handling of flat plates or large cylindrical shapes.

Barrel Hooks (S-377)

Description:

Forged carbon steel, Quenched & Tempered.
Meets the performance requirements of Federal Specification RR-C-271G, Type V, Class 6, except for those provisions required of the contractor.

Weld-On Hooks (BH-313)

Description:

Forged alloy steel.
Designed for attachment to mobile lifting equipment to provide a pick point for easy sling attachment.
Large weld pad.
Heavy duty latch interlocks with the hook tip.

Crosby® Forged Swivels

Sorting Hook (A-378)

Sorting Hook with Handle (A-378)

Regular Swivels (G-402)

1/4" - 1 1/4" Size

Jaw End Swivels (G-403)

1 1/2" Size

Description:

Forged carbon steel, Quenched & Tempered.
Pressed steel latches and stainless steel springs, bolts and nuts.
Hook body galvanized.

Description:

Easily attaches to any chain and electric hoist with welded link load chain, roller chain or wire rope with suitable end fitting.
Swivel jaw is forged.
Suitable for positioning before lifting.

Description:

G-402 swivels meet the performance requirements of Federal Specification RR-C-271G, Type VII, Class 2, except for those provisions required of the contractor.

Description:

G-403 swivels meet the performance requirements of Federal Specification RR-C-271G, Type VII, Class 3, except for those provisions required of the contractor.

Crosby® Tapered Roller Bearing Swivels

Equipped with tapered roller thrust bearing.
Suitable for frequent rotation under load.
All swivels individually proof tested to 2 times the Working Load Limit with labeled documentation.
All hooks furnished with latches assembled.
All jaws complete with bolts, nuts, and cotter pins.
Pressure lube fitting provided.
NOT TO BE USED ON DEMOLITION (WRECKING) BALLS.

JAW & HOOK

JAW & JAW

JAW & EYE

EYE & JAW

EYE & EYE

EYE & HOOK

Crosby® Angular Contact Bearing Swivels

Designed for high rotation speed, lower torque required to initiaterotation.
Angular contact bearings maximize efficiency, reliability, and service life of swivel and extend the life of the wire rope.
Entire swivel is zinc plated to resist corrosion.
Individually Proof Tested to 2 times the Working Load Limit with certification.
Hook models utilize genuine Crosby hooks which are forged alloy steel, quenched and tempered, and contain patented QUIC-CHECK® markings.
Each swivel 8.5 short Tons and larger is furnished with a pressure lubrication fitting.

Choker Hooks

Crosby Sling Saver hardware meets the requirements for minimum stock diameter or thickness, and effective contact width shown in the Recommended Standards Specification for Synthetic Polyester Round Slings by the Web Sling & Tie Down Association. WSTDA-RS1.

Bolt Type Sling Shackle (S-252)

Screw Pin Sling Shackle (S-253)

Web Sling Shackle (S-281)

Web Connector (S-280)

Sling Hook

Sliding Choker Hook

(S-281)

Synthetic Sling Hook

(WSL-320A)

Sling Connector

High Performance Sling Connector (S-237)

High Performance Sling Connector (S-238)

Spool & Link Plate

Spool (S-255)

High Performance Sling Connector (S-256)

Speedbinder

EFFICIENT & ERGONOMIC LOAD SECUREMENT TECHNOLOGY

Speed binders is changing the load binder industry with its patented Torque Drive technology. Our line of products provide considerable time saving benefits for drivers as well as enhanced benefits by eliminating repetitive, straining operations.

TD-66 (Blue Marking)

TD-92 (Red Marking)

TD-13 (Green Marking)

Load Binder

Standard Lever Type Load Binders (LEBUS L-150)

Snubbing Load Binders (LEBUS L-150)

Walking Load Binders (LEBUS A-1W)

Standard Ratchet Type Load Binders (LEBUS L-140)

Binder without Links and Hooks (LEBUS R-10)

Forged steel – Quenched & Tempered.
Meets or exceeds requirements of US DOT FMCSA Part 393 Subpart I.
Upgraded for use with Grades 70, 80 and 100 Chain
New design one piece forged handle.

Continuous take-up feature provides finite adjustment to tie down load.
One piece assembly, no bolts or nuts to loosen.
Meets or exceeds requirements of US DOT FMCSA Part 393 Subpart I.
Matches the Working Load Limit of Grade 100 chain except for 5/8" size.

Clevis Link

Double Clevis Link

(S-247)

Designed for linking all popular sizes of Grade 3 and Grade 4 chain to rings, end links, eye hooks, pad eyes, tractor eye bolts, etc.

Twin Clevis Link

(S-249)

Available in three popular sizes.
Twin Clevis design provides a variety of uses and can be used with Grade 3, Grade 4 and Grade 7 chain.

Turnbuckle

Hook & Hook

(HG-223)

Eye & Eye

(HG-226)

Jaw & Eye

(HG-227)

Jaw & Jaw

(HG-228)

TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY

End fittings are Quenched & Tempered or normalised, bodies heat treated by normalising.
Crosby’s Quenched & Tempered end fittings and normalised bodies have enhanced impact properties for greater toughness at all temperatures.
Hot-dip galvanised.
Hooks are forged with a greater cross sectional area that results in a stronger hook with better fatigue properties.

Meets or exceeds all the requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, these turnbuckles meet other critical performance requirements, including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
Meets the performance requirements of Federal Specifications FF-T-791b, Type 1 Form 1 - CLASS 4, and ASTM F-1145, except for those provisions required of the contractor.